Linksys router setup with the help of a Cable Internet Service is effortless and can be done either by installation CD or manually configuring the router’s settings. For Linksys Wi-Fi Routers, it is suggested to utilize the Linksys Connect Software.  

 QUICK TIP: If you are not sure about your Internet connection, then contact your Internet Service Provider (ISP).

 To mark the Linksys wireless router setup, you are required to perform four procedures with the help of the computer system that is registered to your ISP:

  • Verifying whether your Internet connection is active 
  • Connecting the devices together
  • Checking and verifying your router’s LEDs
  • Configuring the Linksys router for better Cable Internet connection 

QUICK TIP: To reconfigure a previously used wireless router, reset it to factory default settings. To mark this, press the Reset button of the router for at least 10 seconds. The Reset button is mainly located at the back of your router.

 Verifying whether your Internet connection is active

 Connect your computer system to the Cable modem with the help of an Ethernet cable. If your computer device is getting an Internet connection, you can move further, else contact your ISP. 

  This is the first step to follow to answer, how to set up the Linksys router.

how to set up the linksys router

NOTE: Some cable modem has its own USB ports configured with the ISP to offer your computer system the Internet connection. If the connection is through a USB port, then you will be unable to be online through an Ethernet connection. Contact your ISP(internet service provider) if you want the Ethernet port of the modem configured.

 Connecting the devices together    

Step 1:

Try and connect the cable modem either to the router’s WAN or Internet port.    

8 port internet router linksys

Step 2:

 To proceed with Linksys wireless router setup, connect your computer system to any router’s numbered ports (1, 2, 3, or 4). If you are dealing with a wireless computer, then you will be required to connect it with an Ethernet cable first.

NOTE: In the below-given picture, a computer device is connected to port number 2.

linksys cable modem router

Step 3:

 Connect a power adapter of the router to the power socket.

 Checking and verifying your router’s LEDs

 Once the devices are connected, look at the lights that are located on the front panel of your router. Make sure that the lights corresponding to the ports are lit, where the Ethernet cables are connected. 

Configuring your Linksys router for cable net connection

Step 1:

 To answer, how to set up the Linksys router, access your router’s web-based setup page. Open a web browser and then enter “192.168.1.1” in the address bar and then press the enter key.

192.168.1.1

Step 2:

 Next, you will be asked for the login details. For this leave the User name field blank and type “admin” in the area given and then click on OK.

NOTE: If in any case, you receive an error message after keying the router’s password, it means that the password you have entered is incorrect. Try using the router’s web-based setup page once again and type the correct password.

linksys router web based setup page

Step 3:

On the Setup tab, click MAC Address Clone.

NOTE: A MAC Address is a unique identifier that is pre-assigned to the network adapter of your computer system. This is used by most Cable ISPs for authentication so that subscribers can effectively establish an internet connection.

 You are required to enable the MAC Address Clone feature for the Linksys router to work with your ISP. This will permit your ISP to recollect the router as the computer device with the registered MAC (Media Access control) Address.

Step 4:

 Now, choose Enabled then tap on Clone My PC’s MAC.

mac address clone

Step 5:

Click on .

Checking the internet connection 

 Linksys router setup has one significant step that once the feature is enabled, your internet status should be active. To check the status of the internet connection, follow the steps given below.

 NOTE: Make sure that your Internet Connection Type is set to Automatic Configuration – DHCP.

Step 1:

 Tap on the Status tab.

Step 2:

 Verify the Internet IP Address. If it indicates the numbers, it means the wireless router has been appropriately configured. If the IP Address values are showing  0.0.0.0, click on Release IP Address and then Renew IP Address buttons.

NOTE: For the Wireless-B and Wireless-G home routers, tap on the DHCP Release and DHCP Renew buttons.

 You must now be able to access your Internet and if not, power cycle the modem, then your router, and then your computer. 

 IMPORTANT: Power cycling the cable modem must be done with caution. Most of the Cable modems are bundled with Cable TV as well as a phone connection. Some of the Cable modems also featured with backup batteries that help prevent it from being powered OFF even if the adapter is detached from it. 

 To perform the power cycle process follow the steps given below:

Step 1:

 First of all, power OFF your modem. 

 Step 2:

 While your modem is OFF, unplug your power adapter from the wireless router and then shut down your computer.

 Step 3:

 Power ON your modem and then wait for its lights to go steady.

 Step 4:

 Now, power ON your router and then wait for its lights to go steady and then turn ON the computer system.

 Your Internet connection must now be active.

If you are still not able to go online, contact your ISP(internet service provider) to reconfigure your modem.

 Utilizing your network

 Once you have completed Linksys wireless router setup, now you can easily connect your wireless devices to the network. 

Linksys router reset

This portion will guide you about how to reset your wireless router to its factory defaults and how to change your Linksys router password. We will discuss them under three sub-sections, that are:

  • Resetting the Linksys router to factory defaults. 
  • Resetting the router using the web-based setup page. 
  • Changing the Linksys router password.

Resetting the Linksys router to factory default settings

If you are not able to access your router’s web-based setup page or if you have forgotten your router’s password, you can easily reset your router to its default factory settings and to do this, press and hold the Reset button for at least 10 seconds.

 NOTE: Resetting the router to its default factory settings will also help in resetting your router’s password. The Linksys default password is “admin”, and you have to leave the username field as blank.

 IMPORTANT: Ensure that the Power LED of your router is flashing when you are pressing the Reset button. This determines that the router is being reset effectively.

NOTE: The place of the Reset button varies from model to model. Earlier Linksys devices require the pressing and holding the Reset button for around 30 seconds to complete the reset process.

Once you have press the Reset button, unplug and then re-plug the router’s power adapter.

NOTE:  The Power LED of your router will keep on blinking for a few seconds after completing the reset process as it is still trying to stabilize. If the Power light still doesn’t convert solid after a minute then power cycle the router.  

Resetting the router using the web-based setup page

Step 1:

 Firstly, access your router’s web-based setup page. 

Step 2:

Now, click on the Administration tab and then click on the Factory Defaults sub-tab.

Step 3:

 Click on the Restore Factory Defaults button, under the factory default section.

After resetting the Linksys router to its factory default settings, reconfigure it depending on your Internet service. 

NOTE:  The LED of your router will keep on flashing for few seconds after marking the reset process as it is still trying to stabilize and if the Power light didn’t turn solid after a minute then power cycle the Linksys router. 

Changing the Linksys default password

Linksys default password is “admin”, and for the username, you can leave it blank, and for security purposes, it is suggested to change your Linksys router password.

QUICK TIP:  Changing the Linksys router password via a web-based setup page can prevent you from using the Linksys Connect software. If you have already installed the latest version of your software, then it will automatically ask you to enter the new password that you have saved in the web-based setup page

Step 1:

 Firstly, access your router’s web-based setup page.  

Step 2:

 Then click on the Administration tab.

Step 3:

 Enter the new password in the Router Password and Re-Enter to Confirm fields, under the Management section.

NOTE:  You can use a combination of letters as well as numbers for the router password. Ensure that you have taken the note of your router password so that you can have a back-up if you forget it.

Step 4:

Click on Save Settings.

IMPORTANT:  All the computer systems that are connected to the network will be working with the new password at the time of logging in to the Linksys router’s web-based setup page.

The Linksys router’s administrator username, as well as password, are entirely different from the wireless network name (SSID) and the passphrase of your wireless network.

If you are still facing issues in changing or resetting the Linksys router’s administrative password, then you can upgrade your Linksys firmware. 

 Linksys router address

Your Linksys router’s default local IP address (also known as the Default Gateway) is 192.168. 1.1.

 Linksys router login IP

Step 1:

Firstly, open your web browser and then type in the Linksys router login IP of your router (192.168.0.1 by default).

Step 2: 

Type the username that is admin and password that is blank by default and then click on OK or Log In button.

By following such simple steps, you can easily mark the Linksys router login.

 Access router settings 

Step 1:

Firstly, verify whether your mobile phone is connected to the same Wi-Fi network.

Step 2:

The next step is to obtain the IP address.

Step 3:

Click on the Settings app and then tap on the Network and Internet tab and then proceed with how to access the router.

Step 4:

Click on the SSID of your network, on the WiFi screen. Then the Network Info screen will appear.

Step 5:

Kindly note the Linksys router address of your router beside Gateway.

Step 6:

 Enter ipconfig and then press the Enter key, in the command window.

Step 7:

Enter the IP address of your router in the address bar of the new browser tab on your mobile phone.

Step 8:

Now, the router’s login page will appear by using this how to access the router settings from the phone guide. Give the username as well as the password to log in to the router’s configuration page.

 How to login to the router

Just as Linksys router setup was straightforward, similarly answering your question:

How do I login into my Linksys router is also very simple.

For accessing the router settings, you are required to follow these steps:

Step 1.

Connect your computer device to the network. Connect to the same wireless network the Linksys router is on.

Step 2

Move to http://192.168.1.1 in a web browser. This must connect you to the Linksys router.

Step 3

Enter your username in the labelled field. Leave it blank, if you haven’t changed the username from the factory default settings.

Step 4

Enter your password in the password field. Type admin as the password in the password field., if you haven’t changed the password from the factory defaults.

Step 5

Finally, click on Log In.

Manually upgrading the firmware of Linksys WiFi router.

Firmware are error fixers and functionality enhancement of your router.

Linksys firmware updates are very crucial because they resolve the problems or issues that you may face while using your router. Your router is capable enough of either an automatic or manual firmware update.

To avoid upgrade failures, the following items must be appropriately checked:

  • Try to use a wired computer system for better and long-lasting connectivity.
  • If your default web browser is not working properly, then use another stable browser.
  • Download correct firmware from the Linksys support site.
  • If any storage device is connected to the router then before upgrading the firmware, remove it and then start the upgrading process.

This article will let you know about the steps on how to upgrade the Linksys firmware manually.  

To avoid upgrade failures, the following items must be appropriately checked:

  • Try to use a wired computer system for better and long-lasting connectivity.
  • If your default web browser is not working properly, then use another stable browser.
  • Download correct firmware from the Linksys support site.
  • If any storage device is connected to the router then before upgrading the firmware, remove it and then start the upgrading process.

Before upgrading Linksys firmware, you have to complete these steps

  • Check the model as well as the version of the router
  • Download the firmware
  • Perform the upgrading process

NOTE:  Steps, as well as images, may vary according to your wireless router’s model.

Checking the model and version of your router

 First of all, you should find the model number as well as a serial number on the router’s label that is at the bottom of the device. 

 NOTE: Identifying the appropriate model along with version number, will help you in downloading the correct and appropriate Linksys firmware. If in case your router has no version number, it means that your router is a version 1 model. 

Downloading the Linksys firmware

Download the firmware from the Linksys Support Site to your chosen destination folder like desktop or any other location in your computer system.  

NOTE:  The firmware format of your router is .bin. However, there are some different extensions, such as .img and .bix.

Performing the upgrade

Step 1:

 To commence, firstly open a web browser and then type “192.168.1.1” in the Address bar and then pressthe Enter key. If the device IP address does not work or in case if it has been changed, look for your router’s local IP address. 

Step 2: 

 Type in your login essentials. The Linksys default password is admin and if you have changed your password then, in that case, use that instead.  

 Step 3:

 Now, click on Administration > Firmware Upgrade.

 Step 4:

 Click on the Browse… button.

 NOTE: Some of the routers have a Choose File button. 

 Step 5:

 Locate and choose the file that you have downloaded earlier then click on Open.

 NOTE: If you are working with Mac OS X®, then click on the Choose button.

 Step 6:

 Next, click on the Start Upgrade button.

 IMPORTANT: Do NOT turn OFF the power or press the reset button of the router means does not create any type of disturbance during the upgrade procedure.

 If in case, you have chosen an incorrect file, a prompt will appear. Click on the OK button and then repeat Steps 2 to and choose the correct file.

 Step 7:

 Click on Continue when it prompts that the upgrade has been complete.

 Step 8:

 Turn your router OFF then again turn it ON.

 Now, your router must have a manually upgraded Linksys firmware.

How do I know if my router is working properly

This part will answer your query:

How do I know if my router is working properly?

You will know about how to verify if your Linksys router is properly functioning once it is connected.

Before you check if your router is working properly, ensure the Linksys connect means whether the switch is Properly connected to your router. 

Follow the guidelines given below to check if the Linksys router is working effectively when connected to the switch.

Check the LED located on the Linksys router

Ensure that the LEDs located on the switch are lit properly, and it corresponds to a port where your wireless Linksys router is connected to. 

Check the Linksys router address of the connected devices

Ensure that the computer system that is connected to the switch is receiving an IP Address from your Linksys router or the DHCP server.

Ensure that all the computers that are connected to the switch belong to the same network

The IP Address of each and every computer in a single network is assigned by your wireless router. If you have dozens of computers connected on a switch that happens to be connected to your Linksys router, they must belong to a single network.

To test if your router is working properly, try and ping one computer using another computer system in the same network. Your computer’s firewall should be disabled as well. 

IMPORTANT: The following switch models: EZXS16WEZXS88WEZXS55WEG008WEG005WSE1500SE2500, and SE2800 are considered as non-manageable switches. It means that we are not required to configure these before using them. Firmware up-gradation is not significant for these devices.

Linksys router setup without an internet connection

If you want to know about how you can set up your router without an internet connection, read the steps mentioned below. 

Let’s begin:

Step 1: 

Firstly, link the modem as well as your Linksys router to commence the Linksys router setup (without internet). Next to setup router without the Internet, connect your computer to any of the 4 LAN ports of your Linksys router.

Step 2:

Now, turn off the broadband modem, Linksys router, and computer system then turn it  ON once again. Wait till the booting up process is finished.

Step 3: 

Open the internet browser and then type your Linksys router’s IP address in the URL section, click on the search icon.

Step 4:

 After that to proceed with the Linksys router setup without the Internet, you will be required to log in to your Linksys router. Type admin as well as password in the username and password field. You have to keep one thing in mind that both the password and username are highly case sensitive.

Step 5: 

In any case, the password you have typed is not working and helping you to switch with the login page, it may be because you have changed your Linksys router password. Try entering the password that you set. 

Step 6: 

If the setup wizard screen appears, then you will be required to choose yes and then click on next. Once you have done this, the wizard is going to detect the type of connection it supports. If it is a cable connection, the wizard is going to pop up a dynamic IP address.

Step 7: 

To mark the Linksys router setup without internet, choose next, and then save the settings. You must not make any of the changes in the settings that are set by default until it is highly required.

Step 8: 

To check out whether you are connected to the internet, go to the maintenance section, and then click on the router. View at the location bar and then verify whether you have a key in the valid and correct IP address or not.

So, these were some of the steps that one can follow to finish the Linksys router setup without the internet.